Category: All About Guns
Starting in 1976 I have been to Gunsite more times than I can remember. Besides meeting life-long friends, one of the best things is the networking always taking place.
At a three-day revolver/lever-action rifle event last year, I took my Colt New Service and a Model 92 Winchester, both chambered in 45 Colt. Records show my revolver was made in 1907 — roughly half a century before I was born. Two years after this one was made, the U.S. Army adopted it as the Model 1909, two years before the iconic 1911 became the standard issue sidearm.
I love my Pythons, and K- and L-Frame Smith & Wessons, but I have a soft spot for the older revolvers, especially the large frame Colts. Mechanically this revolver was in good shape and I have used it at several Gunsite events.
However …
The exterior was another story and I confess toying with the idea of refinishing the big Colt. The original blue was about 60 percent and showing honest use. This was not a concern as I believe such wear shows character. There were, however, some nicks and scratches I wanted to correct.
Among other things the bottom of the frame appeared as though it had been used for hammering something — I like to think it was from hanging up a wanted poster from some long-forgotten Arizona desperado.
Before: Denny’s 1907 Colt New Service before refinishing.
After: Denny’s beautiful Colt New Service after restoration. It’s ready for another century or more of good shooting!
Decisions
After much internal debate I finally decided to give the old war horse a facelift.
At the Gunsite event mentioned above I met a young man by the name of David Fink. Fink has, among other things, both a Gunsmith Master Certification and a Gunsmith Advanced Certification to his name. Dave offers custom gunsmithing, custom rifle and pistol builds, machining and prototyping, along with re-bluing and Cerakote coatings. In short, it’s a full service shop.
I saw several examples of Fink’s work at Gunsite, including refurbishing and re-bluing a beat-up Smith & Wesson Model 10. All examples I observed showed superb workmanship so I made arrangements with Dave to remove the imperfections and re-blue my revolver.
After acquiring a pair of ivory stocks with gold Colt medallions from N.C. Ordnance to replace the original worn, hard rubber grips, I gave the Colt to Dave. The only thing left was the anticipation of receiving back the finished sixgun, reload some more 45 Colt and head to the range.
As custom work goes, I didn’t have long to wait as Dave completed the revolver in six weeks!
Before: The bottom of the frame showed dents as if it had been used as a hammer.
Maybe from hanging up a wanted poster from a long-gone outlaw?
After: Look Ma! No dings! All the dents were removed from the frame.
The Facelift
In addition to the damage on the bottom of the frame mentioned above, the cylinder had deep scoring caused by a sharp burr on the front sideplate screw from a previous owner. There were some small dings on the top strap of the frame as well as on the barrel towards the muzzle.
The Rampant Colt logo and inspector stamp were very shallow and I asked Dave to retain them during finishing if at all possible. He was able to retain the markings on the sideplate and the marking “New Service 45 Colt” on the barrel is still crisp and clear.
Dave recontoured the previously burred sideplate screw and fit it flush with the frame. The overall finish is a bright, polished blue and is so deep it is reminiscent of the finish applied to Colt and Smith & Wesson years ago.
The nitre-bluing process (sometimes referred to as fire bluing) can produce a wide range of colors from light yellow to super bright “peacock” blue. Dave finished the screws, trigger, hammer, cylinder release, lanyard ring and ejector rod head in a gold color to contrast with the bright blue and compliment the gold medallion in the stocks.
The completed restoration was more than I could have hoped for. At the risk of sounding melodramatic, it was simply stunning.
Before
After
100-lb. Trigger
The double-action trigger pull on my New Service was light — as long as you had a mule handy to hitch to it! The pull weight bottomed-out every gauge I own. The single-action pull wasn’t much better, being roughly the same as the double-action pull in many revolvers. I asked Dave to lighten it up some if he could.
Colt revolvers use a “V”-shaped mainspring. One method of lightening the trigger pull is to put something between the upper and lower leg of the “V” and bend the top leg upwards. This method sometimes barely lightens the trigger pull and if bent too much, it results in unreliable ignition.
Dave tried the above technique, but because the 112-year-old spring was so brittle, it snapped before any bend could be made. He ordered a new main spring and much to his and my surprise, the double-action trigger pull was now at a very manageable 9 lbs., with single-action breaking at a crisp 2.5 lbs.
Proof Test
I couldn’t wait to shoot it and despite the temperature being in the mid-30s with drizzling rain, I went to the range the same day I picked it up, along with a quantity of Keith-type 255-gr. semi-wadcutter rounds. To my great satisfaction the old revolver was more accurate than before. The restoration itself had nothing to do with the increased accuracy but it can be attributed to the much lighter trigger pull, allowing a smoother press while the sights were on the target.
Any new finish will add a few thousandths to the thickness on the metal surface. As a result, there was a barely perceptible hitch in the cylinder release. I have no doubt this will disappear with use as the parts wear in.
A friend remarked the old Colt is now too pretty to carry. However, I don’t own any “safe queens” and I’m looking forward to more trips to Gunsite to put some honest holster wear back on the old warhorse.
Duke’s Colt SAA .45 remodeled with Peacemaker Specialists’ 1880s Package.
After 50 years of buying Colt Single Action Army revolvers in many calibers and all generations, I had never actually had one custom-made to my specs. Of course, I’ve had special ivory, bone or fancy wood grips fitted and I’ve had special-order barrel lengths such as a 3rd Generation .38-40 with a non-cataloged 4″ barrel with matching ejector rod and housing.
The gorgeous color-case-hardened hammer now matches the frame.
Going OIld-School
Recently in a conversation with Eddie Janis, head of Peacemaker Specialists located in Paso Robles, Calif., he mentioned his “1880s Package.” It consists of taking a 3rd Generation SAA with the so-called “black powder” frame and remodeling it to duplicate an 1880s Peacemaker as closely as possible. Now, I’ve been friends with Eddie for over 20 years and had him slick up the internals on a couple of Colts, and purchased items from his extensive inventory of parts for all generations. After he described the alterations for a 1880s Package, I got to thinking — “I’m now approaching my seventh decade. If I want to have a special Colt, it better get in the works.” So it did!
Let me describe the 1880s Package. Please note any of the services mentioned next can be purchased individually and the customer does not have to go for all of them.
Here’s the list — the barrel and all blued parts are cleaned of finish and markings, then restamped as they would have been in the 1880s. The cylinder flutes are lengthened and front of flutes beveled. Beveling is also done to the front of the ejector rod housing, and toe and heel of grip frame. The hammer spur is checkered and outlined and hammer is color case hardened. The other parts, after cleaning and re-marking, are then rust blued.
After the cosmetics, there is the inside of the Colt to consider. First off, I’m sad to say the internals of third Generation SAAs are often a mess. They usually function OK but most specimens are gritty and heavy when cocking the hammer. Likewise with the trigger pull. Cylinder looseness is a gripe often mentioned by new buyers.
Peacemaker Specialists makes all those problems go away. When I received my gun back, its action was remarkable. Cocking the hammer made me wonder just how it could be so smooth and light, without any sideways wobble the 3rd Generation hammers sometimes have. Trigger pull was right about 3 lbs. with absolutely no creep or grit and the cylinder — how can it be so tight, both with hammer cocked and at rest? There is not one iota of shake either laterally or fore and aft. It baffles me.
The Raw Material: Duke’s second — and final — candidate for customization
came from the Colt factory as a 7.5″ barrel .45 Colt.
Caliber stamp on barrel in the white during the Peacemaker Specialists remodeling
compared with current style of caliber stamp.
Stocking Up
When it comes to handgun stocks, I’m a bit of a nut job. Hardly any of my handguns wear factory issue stocks except the military collectibles. Factory stocks are usually too thick, too thin or just too ugly for me. Contrary to many Peacemaker lovers, I’m not big on ivory stocks as a grip material although I do have some. Bison bone is a great material for SAA stocks but the fellow who made mine is now deceased. The truth of the matter is I’m simple in my tastes and prefer good American (black) walnut. I instructed Eddie to use ordinary straight grain walnut as Colt would have used circa 1880 and to make them one piece as Colt did. They fit perfectly.
I didn’t go for one service offered by Peacemaker Specialists — a new cylinder, made by rechambering a smaller caliber cylinder so the chamber mouths match .45 Colt barrel groove diameter. Colt SAA .45s have 0.451″ barrel groove diameter as standard but their cylinder chamber mouths usually run 0.455-457″. The redone cylinders offered by Peacemaker Specialists have 0.452″ chamber mouths. For years, I’ve preached against Colt putting those huge chamber mouths in .45s, so why didn’t I go for the smaller size with this SAA?
The answer is logistics. I have a dozen other .45 Colt revolvers, most with those huge chamber mouths. My .45 Colt handloading is usually with softer 1:20 tin-to-lead alloy bullets sized to 0.454″. This system gives more than adequate accuracy from all my .45 sixguns. Thus, I wanted to leave the cylinder chamber mouths of this special .45 the same dimension so I didn’t have to load different .45s rounds for it.
Keepin’ it real: Duke chose straight-grain walnut stocks (right) on his remodeled
1880s SAA instead of fancy walnut grips (left) fit for a dude!
These parts were sent back to Duke “in the white” during the work so they could be photographed.
Of Pins And Locks
From introduction in 1873 until the mid-1890s, Colt Peacemakers had their cylinder base pins secured by a screw angling in from the front of the main frame. In the 1890s, Colt began phasing this system out in favor of a transverse spring-loaded lock. Somehow, the first system got the moniker “black powder frame” although Colt did not guarantee SAAs for smokeless powder ammunition until 1900. Therefore both frame styles were actually sold prior to the smokeless powder warranty.
Regardless, for Peacemaker Specialists to do a true 1880s package the customer must supply them a “black powder frame” sample on which to work and it’s actually not as easy as it sounds. Colt reintroduced a limited number of black powder frames in their 1873-1973 Peacemaker Centennial Commemoratives. In the 1980s, with their 3rd Generation production, Colt began to offer black powder frame SAAs as a custom shop option and continued to do so albeit intermittently into the 21st century. They do not offer them now. The only option for people like you and me is to find one on the Internet or sitting in a gun shop.
After my conversation with Eddie Janis about the 1880s Package I began perusing Gunbroker.com for a black powder frame 3rd Generation .45. Initially, I wanted it with a 4-3/4″ barrel so Peacemaker Specialists could re-mark it with the old style double address line. It took a few months of Internet searching but I finally found a 4-3/4″ .45 back in Kentucky. Once it arrived, I fired it 10 rounds, hit the stump of wood I aimed at every time and shipped it right to Eddie
Left is the factory cylinder, while right is the “new” cylinder. Note the bigger
bevels at the end of the cylinder and larger flutes.
Project Hits A Snag
Soon Eddie called and in an almost regretful tone told me essentially the following — “A friend wouldn’t build something for a friend knowing it was going to come out substandard in the end.” My quickly bought-and-shipped 4-3/4″ .45 was manufactured during a time when Colt was having problems with fit and finish of third Generation SAAs. He pointed out several flaws I should have noticed so he returned it and my search started again.
After a couple months I hit the jackpot upon encountering a new-in-box 7-1/2″ SAA made in 2008. It was a beauty. Although I wasn’t going to get my two-line address, the 7-1/2″ length is actually my favorite for shooting. It was sent to California and Eddie approved of it.
The checkering done on Duke’s SAA hammer spur to match an 1880s hammer spur.
Unfortunately, the firing pin cannot be changed to match an 1880s model.
Waiting, Waiting …
To make a long story short, months passed but finally my new old gun arrived back home. It’s a beauty!
How does it group on paper? Darn if I know; having never shot it on paper. I can hit steel or wood time and time again despite my 70-year-old eyes. Even better, those eyes can bask in the Peacemaker’s radiance when taking a break at my word processor because I’ve been keeping it near me on my desk.
The Ingram Model 10, better known as the MAC-10 (Military Armament Corporation) submachine gun, was produced in both 9mm and .45 ACP versions. Here’s everything you need to know about it.
On July 11, 1979, a white Ford Econoline van cruised through the parking lot of Dadeland, urban Miami’s largest shopping mall. Dade-land was fifty acres of late 1970s awesome, populated with niche shops, anchor stores, and throngs of families out doing what Americans did in the years immediately prior to Ronald Reagan.
Among the many shoppers enjoying the mall that day was one German Jimenez Panesso and his bodyguard, Juan Carlos Hernandez. (German was his name, not his nationality.) German Jimenez Panesso was a Colombian drug lord.
Panesso traveled in an armored Mercedes limousine befitting the stature of one of Miami’s top drug dealers. At 37, Panesso was handsome, rich, powerful, and on top of his game. At 2:30 pm on this torrid Miami afternoon, Panesso and Hernandez made their way into Crown Liquors to procure their weekly supply of Chivas Regal. Both men were sufficiently at ease for Hernandez to leave his 9mm Browning Hi-Power behind in the Mercedes.
The Ford van pulled up and parked outside the liquor store. The astute observer would have noted that one side of the van read “Happy Time Complete Party Supply.” The other declared, “Happy Time Complete Supply Party.” The question of whether the van supplied the party or was the party itself I shall leave to the philosophers.
Two men left the van and followed Panesso and Hernandez into the shop. The larger of the two then produced a .380 Beretta pistol equipped with a sound suppressor and shot Panesso four times in the face. His companion hosed the store down with a fully automatic .45ACP MAC-10 submachine gun, in the process killing Panesso’s associate, Juan Carlos Hernandez.
The two assassins returned to the van and liberally sprayed the parking lot and surrounding shops with gunfire apparently just for meanness. Authorities later found the van abandoned behind the shopping center. In addition to quarter-inch armored plate affixed around the vehicle, there were also several gun ports covered with nondescript plastic covers.
Inside the van, the cops found more than twenty firearms including shotguns, handguns, and automatic weapons. Panesso and Hernandez were the 37th and 38th Miami homicides for 1979. At a time when there were untold millions to be made moving drugs into south-central Florida, the MAC-10 submachine gun found its most sinister applications.
Reality
Such sordid stuff as this makes for popular copy. Prose describing unfettered violence catches the eye, and I just crafted a bit of it myself. However, the dirty little secret is that criminal usage of legitimate automatic weapons was and is actually vanishingly rare in the United States. In fact, Thompson submachine guns and Browning Automatic Rifles could be found in Sears and Roebuck stores as well as conventional gun shops prior to the passage of the blatantly unconstitutional National Firearms Act of 1934.
Before the passage of that law, machineguns were sold over the counter and uncontrolled wherever there was money enough to purchase them. It was simply that following on the heels of the Great Depression nobody had any money. A Thompson sold for $225 back then. That’s about $4,400 today. A BAR was the equivalent of about $6,000.
Categories
Dangerous Game Cartridges
DENVER (KDVR) — Multiple shootings sent 11 people to the hospital early Tuesday morning after thousands flocked downtown in celebration of the Denver Nuggets’ historic NBA Finals win, celebrating into the early morning hours.
Just before 1 a.m., the Denver Police Department tweeted that they were investigating a shooting in the 2000 block of Market Street.
DPD said nine gunshot victims were located and that they identified a suspect who also had a gunshot wound.
Three victims were in critical condition at a local hospital, and the other victims appeared to have non-life-threatening injuries, according to DPD.
At around 1:11 a.m., DPD said they were investigating a shooting in an area where one person was shot. However, officers provided an update that the victim was actually shot in a different location and self-transported to the hospital.
In total, 10 people were injured in the 2000 block of Market Street, which is next to Coors Field.
DPD said this shooting is complex and the investigation is in its early stages. Early information suggests that multiple shots were fired during an altercation that involved several people.
Around 11:50 p.m. Monday, DPD said they were also investigating a shooting in an area a block away from the 16th Street Mall and several downtown hotels.
One person was taken to a local hospital, but their injuries were not immediately known.
Officers were working to obtain suspect information.
Having a hand in the specification of a pair of deluxe side-by-sides makes the job of testing even more of a pleasure, and Michael Yardley is excited to see exactly what the guns can do
Having a pair of side-by-sides to test is a luxury and Michael Yardley, after having a hand in the specification of the guns, takes even more pleasure when he takes them out to put them through their paces.
AYA DE LUXE NO 2 SIDE-BY- SIDE
This month’s test concerns a new pair of AyA No 2 12-bore de Luxe sidelock side-by-sides specifically built for grouse shooting, proofed and choked for steel shot. Weighing in at just over 7lb, an ideal weight for a modern 30in game gun – or, indeed, a vintage one – they were ordered from AyA by ASI of Snape, the British importer that also brings in Rizzini from Italy. I must declare an interest before continuing: I helped specify these guns for a friend, but this afforded me the opportunity not only to consider them in much detail, but to handle and shoot them more than I normally would when testing.
First impressions are of an attractive, classically styled and well-stocked pair of guns. The scroll engraving (which is laser cut but hand finished) looks good. While you can tell the difference under scrutiny, I wouldn’t bother, however, paying more for handwork on guns intended for the field (although nothing beats hand-cut Holland or Purdey scroll). Laser engraving techniques have much advanced and suit medium scroll, as seen here, especially well. The stocks of the test guns are well proportioned, longer than the average at 15 3/4in and slightly deeper in the butt sole (at 5 3/8in) too as requested. They are nicely figured Turkish walnut and well finished in oil with hand-cut chequering. I liked the proportions of the grips and the combs. The grip is slim without being too slim. It was also specified that the combs be made a little fuller than the AyA norm.
The guns dry-mount well and feel secure at the shoulder and well anchored. They also have a bit more cast than is typical. This opens an interesting issue. The man for whom they were made – a right-hander shooting off the right shoulder – has a left eye that cuts in a bit more than it should sometimes (as many of us have). The remedy for this would normally be extra cast, but he also wanted guns that handled without feeling too odd or crooked on the moor. He had shot near-standard measurements for a long time.
So, after considerable thought and a little experiment, a compromise was reached. On clay birds, I had noted he didn’t seem too badly affected by eye dominance issues when he focused hard (indeed, he shot well). On the pattern plates, however, the potential problem became more evident. My final advice was to go with extra cast, but not as much as some old-school gunfitters (who loved specifying bent stocks) might have liked.
Breaking with our precedent to leave shooting impressions until the end, I will also note here en courant that it was really gratifying that when he did shoot with these guns for the first time, he was connecting with 90% or more of what was presented. I don’t think he would have done better with more cast – probably worse – and the guns were mounting beautifully. Generally, I always avoid extremes of cast in over-and-unders, but these guns have made me reconsider cast on side-by-sides too. Watching someone shoot should be the final arbiter, not just the pattern plate.
Back to the main plot. A feature of these guns, and another aspect of them where much thought went in, was the barrel specification. They are chopper lump and fleur-de-lys steel shot proofed at tight 1/4 (15 thou or 3/8) in both barrels for lead or steel. Steel shot does not suit tight constriction, but this choking is most efficient with lead too. Having the same choke also avoids the ‘ballistic thrombosis’ of worrying about constriction (in the old days, meantime, grouse guns were sometimes choked a little tighter in the right barrel preparing for what was expected to be a rangier first shot).
What else to say? Well, these are No 2 guns, albeit deluxe ones. AyA does still make its mechanically similar No 1, which is considerably more expensive, benefiting from better wood and engraving, and a finer finish. But, for me, the No 2 de Luxe meets a very acceptable standard for practical use.
TECHNICAL
AyA has long used the pattern of the Holland Royal as the inspiration for its sidelocks. Continental manufacturers making side-by-sides tend to copy the Holland rather than the Purdey design because it is more straightforward to make and, critically, simpler to regulate with its Southgate over-centre cam ejector work. AyA has had huge success with its sidelocks. With actions made from forgings, they have proven themselves extremely reliable. The test guns have the usual AyA features, including disc-set strikers, replaceable hinge pins and chopper-lump barrels – in this case proofed for steel shot and choked at 15 thou constriction right and left. Steel shot does not need any more constriction to pattern well. It is a mistake to over-choke it. I also tend to use a pellet one size bigger now rather than two. These guns have a longer forcing cone better suited to steel shot, but will happily digest conventional lead loads as well.
SHOOTING IMPRESSIONS
Being involved with the specification, I was excited to actually try the AyAs. Aesthetically, it would be hard to better them at the price. Dry handling was good. Balance was on the hinge pins even with the 30in barrels, and the weight was ideal. The first bird was centred, and, happily, so were the next half-dozen, swapping the guns every few shots. On tougher stuff, the AyAs continued to perform well. The 3/8 chokes in both barrels (near ideal for steel) produced good kills with lead too. Even on the 120ft tower, the guns continued to do the business. The combs, a little fuller than the AyA norm, were fine. The extra cast suited. Ejection was excellent. For the price – which is not insignificant – these offer a lot. They are a 10th of the cost of the English equivalent, but would still stand happily in more exalted company.
AYA DE LUXE NO 2 SIDE-BY- SIDE
♦ RRP: £12,900
♦ ASI Ltd, Alliance House, Snape, Saxmundham, Suffolk, IP17 1SW
♦ 01728 688555
Categories